Complete Guide On How To Cut A 60 Degree Angle On The Table Saw

In the wood processing stages, the standard angle cutting always plays a significant role. Carpenters often use table saws to do that.

You can easily use the table saw to cut bevels smaller than 45 degrees but angles more significant than 45 degrees will be difficult.

Don’t worry. The following article will show you the right way to cut a 60-degree angle on the table saw. Check some entry-level table saw buying guide here

  • Step 1: Identify and adjust the suitable angle
  • Step 2: Hold the piece of wood in the perfect position
  • Step 3: Raise the blade
  • Step 4: Cut
  • Step 5: Handle uneven bevels

 

How To Cut A 60 Degree Angle On The Table Saw

General Introduction Of Table Saws

Before I tell you in detail how to cut a degree angle on the table saw, I will introduce you to the table saw.

As the name suggests, the table saw is a saw that has a table-like surface and has saw blades placed on it. Its design is in various sizes with aluminum or cast iron cutting surfaces. So, you can adjust the edge on the table up or down depending on the depth you want.

The table saw is a versatile tool that helps you cut chamfers in wood. The bevel cutting will occur before the assembly of the wooden blocks.

The need to perform bevel cutting will often be for decorative purposes such as interior molding or cabinet decoration.

With bevels, less than 45 degrees, the table saw comes with presets that make it easy to do it. What about a 60-degree bevel? In the next part, we will give you the answer.

 

How To Cut 60 Degree Angle On the table saw

Using the table saw to cut a 60-degree angle will not be too difficult if you read and understand the process below.

 

Step 1: Identify and adjust the suitable angle

In the first step in this process, you must determine and adjust the suitable angle. You should be careful at this step because the slope will no longer be at a 60-degree angle if the measurement is wrong.

First of all, you need to measure the angle, and you just need to subtract 60 from 45 and get a 15-degree angle. Next, you will take the saw blade and place it precisely at a 15-degree angle of the wood you just measured.

 

Step 2: Hold the piece of wood in a perfect position

Keeping the piece of wood in the perfect position to start cutting the chamfer is exactly what you need to do in the second step. You should place the main component of wood vertically and use another wood to hold it still.

In addition, you also need to make sure to keep the position of the amount of wood opposite the blade.

 

Step 3: Cut

It is the most crucial step in cutting a 60-degree angle on the table saw.

Now you need to turn on the machine and push the material up to get a 60-degree cutting angle.

In addition, to avoid cuts and uneven surfaces, you should not use too much force. You also need to make sure to hold the material firmly and can use clamps for better effect.

 

Step 4: Handle uneven bevels

It is entirely normal to have uneven surfaces and angles. Thin wood grain is often the cause of this problem.

It is the part of the saw blade that cannot be touched and handled. This solution is to use a small flat plane like a small sharp knife for wood.

First of all, you need to put the material on top of the base. Next, you will control the planer so that the blade faces forward and runs along the grain direction. You will do this until the uneven surfaces become even and smooth.

Alternatively, you can also use a hand planer for uneven outer corners.

 

Some Notes On Safety Measures

Finally, I’ll give you a few tips to keep you safe during cutting:

  • Must wear rubber gloves capable of withstanding cutting force to guard against the saw blade
  • Wear safety glasses to prevent wood chips from entering your eyes, and wear earplugs to avoid too much noise
  • Do not apply too much force to the table saw
  • Ensure that the saw blade has stopped rotating before adjusting the saw table
  • Do not wear clothes that are too loose and fussy because the saw blade can cut or suck them before you can react
  • Please disconnect the power before removing the battery

 

Conclusion

Thus, the above article has helped you know to cut a 60-degree angle. You can also apply this process when cutting other corners with the table saw. And always make sure it’s safe to do them.

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.